LED Headlamp VIDEX VLF-H057 1700Lm 5000K features focused and wide-angle white light, powerful red and green light modes. Thanks to 16 operating modes, a rear signal light, IP65 dust and water protection rating, and impact resistance up to 1 meter, the headlamp provides a wide range of usage scenarios. The headlamp also supports the Power Bank function — using the built-in USB-A port, you can connect devices for charging. This feature can be especially useful during power outages or when access to the mains is unavailable. The headlamp can be controlled both by buttons on the housing and by hand gestures thanks to the built-in motion sensor. It is powered by two replaceable Li-ion 18650 batteries with a capacity of 2200mAh. HEADLAMP CONTROL The headlamp is controlled using a rotary switch, side button, and touch buttons located on the top and rear parts of the housing. 1. Turning on the light and switching between brightness levels is performed by rotating the rotary switch. To turn on the light at the lowest brightness level, turn the switch one step forward ("away from you"). Continue rotating the switch to increase brightness. This allows quick switching between brightness modes. 2. To switch between focused white light, wide-angle white light, red, and green light modes, press and hold the side button of the switched-on headlamp for 0.5 seconds. 3. To activate the motion sensor mode, press the sensor button once on the switched-on headlamp. The button is located on the top of the housing. The activation of the sensor is indicated by an LED indicator next to the button. When the sensor is active, wave your hand once approximately 5–10 cm in front of the headlamp to temporarily turn it off. Wave your hand again to turn it back on in the previously selected mode. 4. To deactivate the motion sensor, press the sensor button once or turn the rotary switch fully towards you. 5. To turn on the rear signal light, press and hold the rear touch button for 3 seconds while the headlamp is switched on. To turn off the rear signal light, press and hold the rear touch button for 3 seconds again. 6. To switch off the headlamp, turn the rotary switch fully towards you or fully forward. HEADLAMP OPERATING MODES SPOT TURBO – the highest brightness level of focused white light with an output of 1700Lm. Beam distance reaches 286m. Runtime: 2h 45min. Peak beam intensity: 20566cd. SPOT HIGH – brightness output of 500Lm. Beam distance reaches 148m. Runtime: 3h 30min. Peak beam intensity: 5541cd. SPOT MIDDLE – brightness output of 120Lm. Beam distance reaches 79m. Runtime: 16h. Peak beam intensity: 1574cd. SPOT LOW – brightness output of 20Lm. Beam distance reaches 24m. Runtime: 130h. Peak beam intensity: 149cd. FLOOD TURBO – the highest brightness level of wide-angle white light with an output of 550Lm. Beam distance reaches 43m. Runtime: 3h. Peak beam intensity: 479cd. FLOOD HIGH – brightness output of 230Lm. Beam distance reaches 25m. Runtime: 9h. Peak beam intensity: 159cd. FLOOD MIDDLE – brightness output of 90Lm. Beam distance reaches 17m. Runtime: 18h. Peak beam intensity: 73cd. FLOOD LOW – brightness output of 20Lm. Beam distance reaches 7m. Runtime: 85h. Peak beam intensity: 14cd. RED HIGH – brightness output of 42Lm. Beam distance reaches 11m. Runtime: 6h. Peak beam intensity: 31cd. RED MIDDLE – brightness output of 16Lm. Beam distance reaches 5.2m. Runtime: 25h. Peak beam intensity: 6cd. RED LOW – brightness output of 5Lm. Beam distance reaches 3m. Runtime: 100h. Peak beam intensity: 3cd. RED FLASH – brightness output of 5Lm. Beam distance reaches 3m. Runtime: 200h. Peak beam intensity: 3cd. GREEN HIGH – brightness output of 125Lm. Beam distance reaches 24m. Runtime: 18h. Peak beam intensity: 147cd. GREEN MIDDLE – brightness output of 60Lm. Beam distance reaches 16m. Runtime: 28h. Peak beam intensity: 65cd. GREEN LOW – brightness output of 20Lm. Beam distance reaches 8m. Runtime: 152h. Peak beam intensity: 18cd. GREEN FLASH – brightness output of 5Lm. Beam distance reaches 4m. Runtime: 500h. Peak beam intensity: 3cd. The headlamp automatically remembers the last selected color mode and restores it each time the device is switched on until another color mode is selected. CHARGING The headlamp is charged using the included USB-C charging cable. To charge the device, switch it off and remove the protective silicone cover. Connect the USB-A end of the charging cable to a power adapter and the other end to the charging port of the headlamp. During charging, the battery indicator segments will flash, showing the current battery charge level. When the battery is fully charged, all indicator segments will remain continuously lit. After charging, disconnect the cable and securely close the protective cover to prevent water and dust from entering the headlamp. WARNING! It is strictly forbidden to use the headlamp while charging. When the headlamp is switched off, a single press of the side button activates the battery level indicator. The indicator segments are located on the rear part of the housing in the area of the rear signal light. The indication remains visible for 3 seconds unless it is switched off earlier by pressing the power button again. - Five red segments indicate a full charge (100–90%). - Four red segments indicate a charge level of 90–75%. - Three red segments indicate a charge level of 75–55%. - Two red segments indicate a charge level of 55–35%. - One red segment indicates a charge level of 35–10%. - One flashing red segment indicates a charge level of 10–0%. Warranty period is 3 years for the headlamp and 1 year for the batteries. The warranty does not cover accessories.